Husqvarna F2101 Repair Manual Download Page 78

Page: 78 / 310

9 SHOCK ABSORBER, SWINGARM

- When the pressure gauge reaches the required value, turn

control lever

Damper

to Vacuum.

Guideline

3 bar

✓ The pressure gauge drops to the required value.

0 bar

- When the pressure gauge reaches the required value, acti

vate the

On/Off

switch.

Guideline

0 bar

✓ The vacuum pump is switched off.

- Slide O-ring G) to the end of the special tool by the specified

value (distance

minus specified value).

Guideline

5mm

I Depth micrometer (T107S) (

�

p. 296)

- Slide the floating piston into the reservoir to the shortened

position using the special tool.

•

Info

The floating piston must be positioned at exactly

this point when the rod is fully extended; otherwise,

damage will occur during compression of the shock

absorber.

Remove the special tool.
Remove adapter

from connector

of the vacuum

pump.

Info

Hold the damper so that the filling port is at the high

est point.

Remove the adapter.
Mount and tighten screw

@).

Guideline

I Screw, filling port

M10x1

14 Nm (10.3 lbf ft)

411

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Brands by name

Popular brands