Husqvarna F2101 Repair Manual Download Page 218

Page: 218 / 310

17 ENGINE

17.5.7

Installing the spacer

17.5.8

shift shaft, installing

- Grease the shaft seal ring.

I Long-life grease (

p. 282)

- Mount spacer

- Set the crankshaft to top dead center and lock it with

screw

- Slide shift shaft

with the washer into the bearing seat .

17.5.9

shift drum locating unit, installing

17.5.10 locking lever, installing

216

- Push away sliding plate

from the shift drum locating unit,

and position shift drum locating unit

Info

The flat surfaces of the shift drum locating unit are not

symmetric.

- Mount and tighten screw

@).

Guideline

Screw, shift

drum locating

10 Nm (7.4 lbf ft)

Loctite

243

™

- Mount locking lever

with the washer, sleeve, and spring.

- Mount and tighten screw

Guideline

Screw, locking

lever

Shift through the transmission.

6 Nm (4.4 lbf ft)

Loctite

243

™

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands