Husqvarna F2101 Repair Manual Download Page 75

Page: 75 / 310

9 SHOCK ABSORBER, SWINGARM

Turn adjusting screw

all the way clockwise with a

socket wrench.

Turn counterclockwise by the number of turns corre
sponding to the shock absorber type.

Guideline

Compression damping, high-speed

Comfort

2.5 turns

Standard

2 turns

Sport

1.5 turns

Turn adjusting screw @) clockwise up to the last percep
tible click.

Turn counterclockwise by the number of clicks corre
sponding to the shock absorber type.

Guideline

Rebound damping

Comfort

17 clicks

Standard

15 clicks

Sport

13 clicks

Alternative 2

Warning

Danger of accident

Modifications to the sus

pension setting may seriously alter the handling
characteristic.

Extreme modifications to the suspension setting

may cause a serious deterioration in the handling
characteristic and overload components.
-

Only make adjustments within the recom

mended range.

Ride slowly to start with after making

adjustments to get the feel of the new
handling characteristic.

Position adjusting screws@,

fD,

and @) in the location

determined during disassembly.

Bleeding and filling the dam�er

Info

Before working with the vacuum pump, carefully read the operating manual included with the vacuum

pump.

Open the adjusters of the rebound and compression damping completely.

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Brands by name

Popular brands