Husqvarna F2101 Repair Manual Download Page 194

Page: 194 / 310

17 ENGINE

17 .4.12 Installing the drive wheel of the balancer shaft

310342-10

17.4.13 Cylinder - Nikasil

coating

310368-10

- Ensure that woodruff key

is seated properly.

- Warm drive wheel

of the balancer shaft and push it onto

the balancer shaft.
Guideline
1100 °C (212 °F)

Nikasil

is a surface protection layer for a coating procedure

developed by Mahle. The name is derived from the two materials

used in this procedure - a layer of nickel into which is embedded

the particularly hard silicone carbide.

The most important advantages of the

Nikasil

coating are very

good heat conductivity, resulting in much improved performance,

low wear, and a lightweight cylinder.

17.4.14 Checking/measuring the cylinder

310346-10

192

- Check the cylinder bearing surface for damage.

If the cylinder bearing surface is damaged:

- Change the cylinder and piston.

- Measure the cylinder diameter at several locations on

the 0- and 0-axes using a micrometer to identify oval

wear.
Guideline

Cylinder - drill hole diameter

Size I

78.000 ... 78.012 mm

(3.07086 ... 3.07133 in)

Size II

78.012 ... 78.025 mm

(3.07133 ... 3.07184 in)

Info

The cylinder size

is marked on the cylinder collar.

- Using a straightedge and the special tool, check the sealing

area of the cylinder head for distortion.
I Feeler gauge (59029041100) (

p. 288)

Cylinder/cylinder head -

distortion of sealing area

:e; 0.10 mm (:e; 0.0039 in)

If the measured value does not meet specifications:

- Change the cylinder.

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands