Husqvarna F2101 Repair Manual Download Page 199

Page: 199 / 310

1£

1//

EV'§

••

•

17 .4.21 valves, checking

300117-10

310437-10

302809-10

17 ENGINE

Remove the valve spring retainer and valve springs.
Mark the valve springs according to their normal built-in posi

tion.

Pull the valve down out of the valve guide.
Remove valve stem seal

with the special tool.

Valve stem seals plier (77229010000) (

�

p. 291)

Remove valve spring seat

Mark the valves corresponding to their installation position.

Info

Place the valves in a carton corresponding to their

installation position and label them.

Check the valve plate for run-out.

Valve - run-out

At the valve plate

:5 0.05 mm (:5 0.002 in)

If the measured value does not meet specifications:

Change the valve.

Check sealing seat

on valve for damage and wear.

If the sealing surface is damaged or worn:

Machine the valve seat.

197

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands