Husqvarna F2101 Repair Manual Download Page 57

Page: 57 / 310

9.9

9 SHOCK ABSORBER, SWINGARM

Finishing work

Install the shock absorber.(� p. 57)

Check the free travel of the foot brake lever. (

!!JJ

p. 144)

Check the static sag of the shock absorber. (

!!JJ

p. 52)

Check the riding sag of the shock absorber. (

�

p. 53)

- Adjust the rebound damping of the shock absorber. (

�

p. 51)

Remove the motorcycle from the lift stand. (

�

p. 12)

Removing the shock absorber

Preparatory work

Raise the motorcycle with a lift stand. (

�

p. 12)

Main work

Remove the cable ties.

Remove screws

with the washers.

Remove the frame protectors on the left and right.

Remove screw

@).

Remove fitting

Info

Raise the wheel slightly to be able to remove the

screws more easily.

Press angle lever

toward the rear.

Press linkage lever

downward.

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands