Husqvarna F2101 Repair Manual Download Page 74

Page: 74 / 310

9 SHOCK ABSORBER, SWINGARM

311690-10

- Clamp the damper in a bench vise.

Guideline

I Use soft jaws.

- Mount adjusting ring

with the intermediate washer.

Info

The adjusting ring cannot be mounted after the piston

rod has been mounted.

- Fill the damper cartridge about half full.

I Shock absorber fluid (SAE 2.5) (50180751 S1) (

ll!:!l

p. 281)

Lubricate O-ring

of the seal ring retainer.

I Lubricant (T158) (

ll!:!J

p. 282)

- Mount the piston rod carefully.

- Mount seal ring retainer

and slide it under the ring groove.

- Mount lock ring

@).

•

Info

Do not scratch the inside surface.

- Pull out the piston rod until the seal ring retainer is flush with

the lock ring.

- Mount locking cap

of the damper cartridge.

- Bleed and fill the damper. (

!!:!I

p. 73)

- Fill the damper with nitrogen. (

!!:!I

p. 77)

Alternative 1

- Turn adjusting screw @ clockwise with a screwdriver up

to the last perceptible click.

- Turn counterclockwise by the number of clicks corre

sponding to the shock absorber type.

Guideline

Compression damping, low-speed

Comfort

17 clicks

Standard

15 clicks

Sport

13 clicks

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Brands by name

Popular brands