Husqvarna F2101 Repair Manual Download Page 131

Page: 131 / 310

15 WIRING HARNESS, BATTERY

Removing the batte�

Warning

Risk of injury

Batteries contain harmful substances.

Keep batteries out of the reach of children.

Keep sparks and open flames away from the batteries.

Only charge batteries in well-ventilated rooms.

Maintain a minimum clearance from inflammable materials when charging batteries.
Minimum clearance

1 m (3 ft)

Do not charge deeply discharged batteries if charge is already below the minimum voltage.
Minimum voltage before the start of the charge

9 V

Dispose of batteries with less than the minimum voltage correctly.

Preparatory work

Press and hold the kill switch � while the engine is idling until

the engine stops.

Remove the air filter box cover. (

p. 90)

Remove the seat. (

p. 94)

Main work

�

-�

I,...,. .�

:;,

,•

•I

I•�

I!-

•

·<

"�

�

- .....

Pull back the negative terminal cover

and disconnect

negative cable

from the battery.

Pull back the positive terminal cover

and disconnect pos

itive cable

from the battery.

Remove screw

� .

�

·-

•

r·

•

·•

-I

'-1

�

. . .

�

J.,

�

1·'

• �

IEill!llil

Pull holding bracket

forward and take out the battery

toward the top.

129

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands