Husqvarna F2101 Repair Manual Download Page 150

Page: 150 / 310

16 BRAKE SYSTEM

148

- Mount bleeder cover

I Bleeder cover (00029013006) (

�

p. 284)

- Connect the bleeding device.

I Bleeding device (00029013100) (

�

p. 284)

- Open shut-off valve

•

Info

Follow the operating instructions of the bleeding

device.

- Ensure that the inflation pressure is correctly set at pressure

gauge

If necessary, adjust the inflation pressure at pres

sure regulator

G,.

Guideline

I Inflation pressure

I 2 ... 2.5 bar (29 ... 36 psi)

- Pull off protection cap

of the bleeder screw. Connect the

hose of the bleeder bottle.
I Bleeding device (00029013100) (

�

p. 284)

- Open bleeder screw

by approx. one-half turn.

Info

Bleed until fresh brake fluid emerges from the bleeder

bottle hose without bubbles.

- Tighten the bleeder screw.

- Close shut-off valve

- Open the bleeder screw again until brake fluid stops emerg-

ing.

•

Info

This prevents overfilling of the brake fluid reservoir.

- Tighten the bleeder screw. Remove the hose of the bleeder

bottle. Mount the protection cap.

- Disconnect the bleeding device. Remove the bleeder cover.

- Stand the vehicle upright.

- Correct the brake fluid up to marking (!).

I Brake fluid DOT 4 (

�

p. 280)

- Mount and tighten the screw cap with the membrane and 0-

ring.

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands