Husqvarna F2101 Repair Manual Download Page 47

Page: 47 / 310

7 HANDLEBAR,CONTROLS

Danger

Danger of poisoning

Exhaust gases are toxic and

inhaling them may result in unconsciousness and

death.

- Always make sure there is sufficient ventilation

when running the engine.

- Use an effective exhaust extraction system when

starting or running the engine in an enclosed

space.

- Start the engine and let it run idle. Move the handlebar to and

fro over the entire steering range.

I The idle speed must not change.

If the idle speed changes:

- Adjust the play in the throttle cable. (

�

p. 45)

Adjusting the play in the throttle cable

Info

If the correct routing of the throttle cables has already been secured, the fuel tank does not need to be

removed.

Preparatory work

- Remove the right side cover. (

p. 94)

- Remove the air filter box cover. (

p. 90)

- Remove the seat. (

p. 94)

- Remove the fuel tank. (

�

p. 96)

- Check the throttle cable routing. (

�

p. 43)

Main work

- Move the handlebar to the straight-ahead position.

- Push back sleeve

- Loosen nut

Turn adjusting screw

in as far as possi-

ble.

- Loosen nut

C,.

Push cold start button

all the way to the stop.

- Turn adjusting screw

so that the cold start button moves

to the basic position when the throttle grip is turned to the

front.

- Tighten nut

C,.

- Turn adjusting screw

so that there is play in the throttle

cable at the throttle grip.
Guideline

Throttle cable play

- Tighten nut

3 ... 5 mm (0.12 ... 0.2 in)

- Slide on sleeve

Check the throttle grip for smooth opera-

tion.

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands