Husqvarna F2101 Repair Manual Download Page 115

Page: 115 / 310

,::)Jr:

14 WHEELS

Main work

Press the brake caliper onto the brake disc by hand in order

to push back the brake pistons.

Info

Make sure that you do not press the brake caliper

against the spokes when pushing back the brake pis
tons.

Loosen screw

by several rotations.

Loosen screws

Press on screw

to push the wheel spindle out of the axle

clamp.

Remove screw

Warning

Danger of accidents

Damaged brake discs reduce

the braking effect.

- Always lay the wheel down in such a way that the

brake disc is not damaged.

Holding the front wheel, withdraw the wheel spindle. Take the

front wheel out of the fork.

Info

Do not pull the hand brake lever when the front wheel

is removed.

Remove spacers

fD.

IID � [

�[ill

�cs

H00934-10

14.6.2

Installing the front wheel

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

- Always keep the brake discs free of oil and grease.
-

Clean the brake discs with brake cleaner when necessary.

113

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands