Husqvarna F2101 Repair Manual Download Page 28

Page: 28 / 310

6 FORK, TRIPLE CLAMP

B03584-10

200666-10

- Measure the inside diameter at multiple locations of the outer

tube.

Inside diameter of outer

tube

:s; 49.20 mm (s 1.937 in)

If the measured value is larger than the specified value:

- Change the outer tube.

- Check the outer tube for damage.

If there is damage:

- Change the outer tube.

- Check the surface of the sliding bushings.

If the bronze-colored layer

under sliding layer G) is

visible or the surface is rough:

- Change the sliding bushings.

- Check the spring length.

Guideline

Spring length with preload

spacer(s)

475 mm (18.7 in)

If the measured value is larger than the specified value:

Reduce the thickness of the preload spacers.

If the measured value is smaller than the specified value:

- Increase the thickness of the preload spacers.

411

Assembling the seal rin retainer

Info

The steps are identical for both fork legs.

R00014-10

- Mount and grease seal ring

Lubricant (T158) (

�

p. 282)

- Mount and grease O-ring

I Lubricant (T158) (

�

p. 282)

- Position pilot bushing support@).

411

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands