Husqvarna F2101 Repair Manual Download Page 16

Page: 16 / 310

6 FORK, TRIPLE CLAMP

Adjusting the com�ression dam�ing of the fork

Info

The hydraulic compression damping determines the fork suspension behavior.

- Turn white adjusting screw

all the way clockwise.

Info

Adjusting screw

is located at the upper end of the

left fork leg.

The compression damping is located in left fork

leg

COMP

(white adjusting screw). The rebound

damping is located in right fork leg

REB

(red adjusting

screw).

- Turn counterclockwise by the number of clicks correspond

ing to the fork type.
Guideline

Compression damping

Comfort

Standard
Sport

• Info

17 clicks
15 clicks

13 clicks

Turn clockwise to increase damping; turn counter
clockwise to reduce damping.

Ad"usting the rebound dam�ing of the fork

Info

The hydraulic rebound damping determines the fork suspension behavior.

- Turn red adjusting screw

all the way clockwise.

Info

Adjusting screw

is located at the upper end of the

right fork leg.
The rebound damping is located in right fork leg

REB

(red adjusting screw). The compression damping is

located in left fork leg

COMP

(white adjusting screw).

- Turn counterclockwise by the number of clicks correspond

ing to the fork type.

Guideline

Rebound damping

Comfort

17 clicks

Standard

15 clicks

Sport

13 clicks

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands