Husqvarna F2101 Repair Manual Download Page 135

Page: 135 / 310

15.7

Checking the ca�acitor

601204-10

601204-11

15 WIRING HARNESS, BATTERY

Main work

Disconnect the negative cable of the battery.
Measure the current between battery ground (-) and the neg

ative cable.

•

Info

The value of the quiescent current applies only to

vehicles in the original state, i.e. without additional

power consumers.

I Maximum open-circuit

current

1.0 mA

If the measured value is greater than the specified value:

Disconnect the voltage regulator from the wiring har

ness and perform the measurement again.

- Check the capacitor. (

i!i,.!1

p. 133)

Remove the capacitor.

Discharge the capacitor by bridging the two contacts.

Connect the capacitor with a 12 V test lamp on one connec

tor and connect it to the battery as shown in the figure.

•

Info

As the charge of the capacitor increases, the test lamp

becomes dimmer.

The lamp lights up for: 0.5 ... 2.0 s

The capacitor is functional.
The lamp lights up for: < 0.5 s

Change the capacitor.

The lamp lights up for: > 2.0 s

Change the capacitor.

Discharge the capacitor with a 12 V test lamp as shown in the

figure.

•

Info

As the charge of the capacitor decreases, the test

lamp becomes dimmer.

The lamp lights up for: 0.5 ... 2.0 s

The capacitor is functional.
The lamp lights up for: < 0.5 s

Change the capacitor.

The lamp lights up for: > 2.0 s

Change the capacitor.

Install the capacitor.

133

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands