Husqvarna F2101 Repair Manual Download Page 130

Page: 130 / 310

15 WIRING HARNESS, BATTERY

128

Changing the main fuse

Warning

Fire hazard

Incorrect fuses overload the electrical system.

- Only use fuses with the required ampere value.

- Do not bypass or repair fuses.

Info

The main fuse protects all power consumers of the vehicle. It is located in the starter relay housing

under the seat.

Preparatory work

- Press and hold the kill switch � while the engine is idling until

the engine stops.

- Remove the air filter box cover. (

�

p. 90)

- Remove the seat. (

�

p. 94)

Main work

- Pull starter relay

from the holder.

- Take off protection caps@}.

- Remove faulty main fuse (5).

Info

You can recognize a faulty fuse by a burned-out fuse

wiref).

A spare fuse

is located in the starter relay.

- Install a new main fuse.

I Fuse (58011109110) (

�

p. 264)

- Check that the electrical system is functioning properly.

•

Tip

Insert a spare fuse so that it is available if needed.

- Mount the protection caps.

- Mount the starter relay onto the holder and route the cable.

Finishing work

- Mount the seat. (

�

p. 95)

- Install the air filter box cover. (

�

p. 90)

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands