Husqvarna F2101 Repair Manual Download Page 100

Page: 100 / 310

12 FUEL TANK, SEAT, TRIM

Main work

Check the throttle cable routing. (

llill

p. 43)

Position the fuel tank and fit the two spoilers to the sides of

the radiator bracket.

Make sure that no cables or throttle cables are trapped or

damaged.

- Attach the hose to the fuel tank breather on the tank lid.
-

Mount and tighten screw

with the rubber bushing.

Guideline

Remaining screws,

chassis

Mount and tighten screws

Guideline

Remaining screws,

chassis

Plug in connector

for the fuel pump.

10 Nm (7.4 lbf ft)

Remove the wash cap set and thoroughly clean the plug-in

connection of the fuel line using compressed air.

Info

Under no circumstances should dirt enter into the fuel

line. Dirt in the fuel line clogs the injection valve!

Lubricate the 0-ring and connect plug-in connection

for

the fuel line.

Info

Route the cable and fuel line at a safe distance from

the exhaust system.

Finishing work

Mount the seat. (

llill

p. 95)

Install the air filter box cover. (

llill

p. 90)

Install the right side cover. (

llill

p. 94)

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands