Husqvarna F2101 Repair Manual Download Page 122

Page: 122 / 310

14 WHEELS

14.7.6

120

Main work

- Loosen nut

- Loosen nuts

- Adjust the chain tension by turning adjusting screws (D left

and right.
Guideline

Chain tension

155 ... 58 mm (2.17 ...

2.28 in)

Turn adjusting screws (D on the left and right so that the

markings on the left and right chain adjusters are in the

same position relative to reference marks f). The rear

wheel is then correctly aligned.

- Tighten nuts

- Make sure that chain adjusters

are fitted correctly on

adjusting screws (D.

- Tighten nut

Guideline

Info

M25x1.5

80 Nm (59 lbf ft)

The wide adjustment range of the chain adjusters

(32 mm (1.26 in)) enables different secondary ratios

with the same chain length.

Chain adjusters

can be turned by 180

Finishing work

- Remove the motorcycle from the lift stand. (

�

p. 12)

Checking the chain, rear sprocket, engine sprocket, and chain guide

Preparatory work

400227-01

- Raise the motorcycle with a lift stand. (

�

p. 12)

Main work

- Shift the transmission to idle.
- Check the rear sprocket and engine sprocket for wear.

If the rear sprocket or engine sprocket is worn:

- Change the drivetrain kit. (

!ill

p. 123)

Info

The engine sprocket, rear sprocket, and chain

should always be replaced together.

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands