Husqvarna F2101 Repair Manual Download Page 132

Page: 132 / 310

15 WIRING HARNESS, BATTERY

130

Installing the batte�

Main work

- Position the battery into the battery compartment with the

terminals facing forward and secure with holding bracket

I Battery (C22S) (

p. 264)

- Mount and tighten screw

Guideline

Screw, battery sup

port bracket

•

Info

10 Nm (7.4 lbf ft)

Contact disks

must be mounted under screws

and cable sockets

with the claws toward the bat

tery terminal.

H00388-10

Recharging the batte

Warning

- Connect positive cable

to the battery.

Guideline

Screw, battery termi- M5

nal

2.5 Nm (1.84 lbf ft)

- Slide positive terminal cover

over the positive terminal.

- Connect negative cable @ to the battery.

Guideline

Screw, battery termi- M5

nal

2.5 Nm (1.84 lbf ft)

- Slide negative terminal cover

over the negative terminal.

Finishing work

- Mount the seat. (

p. 95)

- Install the air filter box cover. (

p. 90)

Risk of injury

Batteries contain harmful substances.

- Keep batteries out of the reach of children.

- Keep sparks and open flames away from the batteries.

- Only charge batteries in well-ventilated rooms.

- Maintain a minimum clearance from inflammable materials when charging batteries.

Minimum clearance

1 m (3 ft)

- Do not charge deeply discharged batteries if charge is already below the minimum voltage.

Minimum voltage before the start of the charge 9 V

- Dispose of batteries with less than the minimum voltage correctly.

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Brands by name

Popular brands