Husqvarna F2101 Repair Manual Download Page 138

Page: 138 / 310

16 BRAKE SYSTEM

136

Move the brake fluid reservoir mounted on the handlebar to a

horizontal position.

Remove screws

Remove cover

with membrane

C,.

Manually press the brake caliper to the brake disc to push

back the brake pistons. Ensure that brake fluid does not flow
out of the brake fluid reservoir, extracting it by suction if it

does.

Info

Make sure that you do not press the brake caliper

against the spokes when pushing back the brake pis
tons.

Remove cotter pins

pull out pin @), and remove the

brake linings.

Clean the brake caliper and brake caliper support.

Check that leaf spring (3 in the brake caliper and sliding
plate @ in the brake caliper support are seated correctly.

Insert the new brake linings, insert pin @), and mount cotter

pins

•

Info

Always change the brake linings in pairs.

Operate the hand brake lever repeatedly until the brake lin
ings are in contact with the brake disc and there is a pressure
point.

Summary of Contents for F2101























































































































































































































































































































Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands

Husqvarna F2101, Repair Manual

Search results

Summary of Contents for F2101

Reviews:

Related manuals for F2101

Brands by name

Popular brands