HIKVISION 607 Series User Manual Download Page 93

Page: 93 / 163

607 Series Face Recognition Terminal

User Manual

Click Add to pop up the Add Card dialog.

Click Card to enter the Card tab.

Select the card type according to actual needs.



Normal Card



Card for Disabled Person: The door will remain open for the configured time period for the
card holder.



Card in Blacklist: The card swiping action will be uploaded and the door cannot be opened.



Patrol Card: The card swiping action can be used for checking the working status of the
inspection staff. The access permission of the inspection staff is configurable.



Duress Card: The door can open by swiping the duress card when there is duress. At the
same time, the client can report the duress event.



Super Card: The card is valid for all the doors of the controller during the configured
schedule.

Summary of Contents for 607 Series




































































































































































Search results

Summary of Contents for 607 Series

Reviews:

HIKVISION 607 Series, User Manual, Page: 93 / 163

Search results

Summary of Contents for 607 Series

Reviews: