manualshive.com logo in svg

HIKVISION 607 Series, User Manual, Page: 124 / 163

Share
Download
HIKVISION 607 Series User Manual Download Page 124

607 Series Face Recognition Terminal

 

User Manual

 

114 

 

 

Table 1. 1

 

Linkage Actions for Access Control Event 

Linkage Actions 

Descriptions 

Audible Warning 

The  client  software  gives  an  audible  warning  when  alarm  is 
triggered. You can select the alarm sound for audible warning.   

Email Linkage 

Send  an  email  notification  of  the  alarm  information  to  one  or 
more receivers.   

Alarm on E-map 

Display the alarm information on the E-map. 

Note:

  This  linkage  is  only  available  to  access  control  point  and 

alarm input. 

Alarm Triggered 

Pop-up Image 

The  image  with  alarm  information  pops  up  when  alarm  is 
triggered. 

7.10.2

 

Event Card Linkage 

Click Event Card Linkage tab to enter the following interface.   

Note: 

The Event Card Linkage should be supported by the device.

 

Summary of Contents for 607 Series




































































































































































Reviews:

No comments