manualshive.com logo in svg

HIKVISION 607 Series, User Manual, Page: 111 / 163

Share
Download
HIKVISION 607 Series User Manual Download Page 111

607 Series Face Recognition Terminal

 

User Manual

 

101 

 

Or you can click Apply Later to apply the changes later in the Permission interface. 

 

The permission changes include changes of schedule and template, permission settings, 
person’s permission settings, and related person settings (including card No., fingerprint, face 
picture, linkage between card No. and fingerprint, linkage between card No. and fingerprint, 
card password, card effective period, etc.).     

7.8

 

Advanced Functions 

Purpose: 
After  configuring  the  person,  template,  and  access  control  permission,  you  can  configure  the 
advanced  functions  of  access  control  application,  such  as  access  control  parameters, 
authentication password, and opening door with first card, anti-passing back, etc. 

Note: 

The advanced functions should be supported by the device. 

Click 

  icon to enter the following interface.   

 

7.8.1

 

Access Control Parameters 

Purpose: 
After  adding  the  access  control  device,  you  can  configure  its  access  control  point  (door)’s 
parameters, and its card readers’ parameters. 
Click Access Control Parameters tab to enter the parameters settings interface. 

Door Parameters 

Steps: 

Summary of Contents for 607 Series




































































































































































Reviews:

No comments