HIKVISION 607 Series User Manual Download Page 112

Page: 112 / 163

607 Series Face Recognition Terminal

User Manual

102

In the controller list on the left, click

to expand the access control device, select the door

(access control point) and you can edit the information of the selected door on the right.

You can edit the following parameters:



Door Magnetic: The Door Magnetic is in the status of Remain Closed (excluding special
conditions).



Exit Button Type: The Exit Button Type is in the status of Remain Open (excluding special
conditions).



Door Locked Time: After swiping the normal card and relay action, the timer for locking
the door starts working.



Door Open Duration by Card for Disabled Person: The door magnetic can be enabled with
appropriate delay after disabled person swipes the card.



Door Open Timeout Alarm: The alarm can be triggered if the door has not been closed.



Enable Locking Door when Door Closed: The door can be locked once it is closed even if
the Door Locked Time is not reached.



Duress Code: The door can open by inputting the duress code when there is duress. At the
same time, the client can report the duress event.



Super Password: The specific person can open the door by inputting the super password.

Notes:



The duress code and the super code should be different.



The duress code and the super password should contain 4 to 8 numerics.

Click Save button to save parameters.

Card Reader Parameters

Steps:
1.

In the device list on the left, click

to expand the door, select the card reader name and you

can edit the card reader parameters on the right.

Summary of Contents for 607 Series




































































































































































Search results

Summary of Contents for 607 Series

Reviews:

HIKVISION 607 Series, User Manual, Page: 112 / 163

Search results

Summary of Contents for 607 Series

Reviews: