Home
/
HIKVISION
/
607 Series
/
User Manual

HIKVISION 607 Series, User Manual, Page: 113 / 163

Share

Page: 113 / 163

HIKVISION 607 Series User Manual Download Page 113

607 Series Face Recognition Terminal

User Manual

103

2.

You can edit the following parameters:



Nickname: Edit the card reader name as desired.



Enable Card Reader: Select Yes to enable the card reader.



OK LED Polarity: Select the OK LED Polarity of the card reader mainboard.



Error LED Polarity: Select the Error LED Polarity of the card reader mainboard.



Buzzer Polarity: Select the Buzzer LED Polarity of the card reader mainboard.



Minimum Card Swiping Interval: If the interval between card swiping of the same card is
less than the set value, the card swiping is invalid. You can set it as 0 to 255.



Max.  Interval  When  Inputting  Password:  When you  inputting the password  on  the  card
reader,  if the  interval  between  pressing two  digits  is  larger  than the  set  value,  the  digits
you pressed before will be cleared automatically.



Enable Failed Attempts Limit of Card Reading: Enable to report alarm when the card
reading attempts reach the set value.



Max. Times of Card Swiping Failure: Set the max. failure attempts of reading card.

«
...
111
112
113
114
115
...
»

Summary of Contents for 607 Series




































































































































































Reviews:

No comments