manualshive.com logo in svg

HIKVISION 607 Series, User Manual, Page: 132 / 163

Share
Download
HIKVISION 607 Series User Manual Download Page 132

607 Series Face Recognition Terminal

 

User Manual

 

122 

 

Click Access Control Alarm tab to enter the following interface. 

 

Steps: 

1.

 

All access control alarms will display in the list in real time. 
You can view the alarm type, alarm time, location, etc. 

2.

 

Click 

  to view the alarm on E-map.   

3.

 

You can click 

  or 

  to view the live view or the captured picture of the triggered camera 

when the alarm is trigged. 

Note: 

For setting the triggered camera, refer to Chapter 7.10.1 Access Control Event Linkage. 

4.

 

Click Subscribe to select the alarm that the client can receive when the alarm is triggered. 

 

1)

 

Check the checkbox(es) to select the alarm(s), including device exception alarm, door event 
alarm, card reader alarm, and alarm input. 

2)

 

Click OK to save the settings. 

Summary of Contents for 607 Series




































































































































































Reviews:

No comments