manualshive.com logo in svg

GigaDevice Semiconductor GD32VF103, User Manual

The GigaDevice Semiconductor GD32VF103 offers a powerful user manual, essential for seamless operation and troubleshooting. Easily access and download the manual for free from our website, ensuring efficient utilization of this remarkable product. Unlock the full potential of the GD32VF103 with our comprehensive and user-friendly manual.

Share
Download
background image

                                                                                                         

GD32VF103 User Manual

 

147 

 

This register has to be accessed by word (32-bit) 

Note:

 Do not configure this register when channel is enabled. 

 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

MADDR[31:16] 

rw 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

MADDR[15:0] 

rw 

 

Bits   

Fields 

Descriptions 

31:0 

MADDR[31:0] 

Memory base address 

These bits can not be written when CHEN in the DMA_CHxCTL register is ‘1’. 

When MWIDTH in the DMA_CHxCTL register is 01 (16-bit), the LSB of these bits is 

ignored. Access is automatically aligned to a half word address.   

When MWIDTH in the DMA_CHxCTL register is 10 (32-bit), the two LSBs of these 

bits are ignored. Access is automatically aligned to a word address. 

 

 

 

Summary of Contents for GD32VF103

























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32VF103

EAW MX250 Owner'S Manual preview
MX250
Brand: EAW Pages: 10
D-Link DFE-690TXD Quick Install Manual preview
DFE-690TXD
Brand: D-Link Pages: 12
Dahua DHI-NVR5224-24P-4KS2 Quick Start Manual preview
DHI-NVR5224-24P-4KS2
Brand: Dahua Pages: 24
dbx ProVocal Specifications preview
ProVocal
Brand: dbx Pages: 2
Accuphase AD-60 Instruction Manual preview
AD-60
Brand: Accuphase Pages: 2
ADTRAN ATLAS 550 Manual preview
ATLAS 550
Brand: ADTRAN Pages: 2
Acrosser Technology AMB-VDX3H1 Series Quick Start Manual preview
AMB-VDX3H1 Series
Brand: Acrosser Technology Pages: 4
AXIOMTEK eBOX532-100-FL Series Quick Installation Manual preview
eBOX532-100-FL Series
Brand: AXIOMTEK Pages: 2
Grizzly PSJ-M3 GEN2 User Manual preview
PSJ-M3 GEN2
Brand: Grizzly Pages: 9
Datasat DDR-16 AES67 Installation And Operating Manual preview
DDR-16 AES67
Brand: Datasat Pages: 24
East Coast Datacom PDS-1/10G User Manual preview
PDS-1/10G
Brand: East Coast Datacom Pages: 19
uneron eSOM3735z Quick Start Manual preview
eSOM3735z
Brand: uneron Pages: 13
Beckhoff EK1122 Documentation preview
EK1122
Brand: Beckhoff Pages: 84
WIN Enterprises PL-83300 User Manual preview
PL-83300
Brand: WIN Enterprises Pages: 25
Behringer X-MADI Quick Start Manual preview
X-MADI
Brand: Behringer Pages: 15
HeimVision HM243 User Manual preview
HM243
Brand: HeimVision Pages: 167
Extron electronics DMP 64 Plus User Manual preview
DMP 64 Plus
Brand: Extron electronics Pages: 99
Domburg Switch Polarization Print HPP4 Quick Start Manual preview
Switch Polarization Print HPP4
Brand: Domburg Pages: 11

Brands by name

Popular brands

Load more brands