GigaDevice Semiconductor GD32VF103 User Manual Download Page 323

Page: 323 / 536

GD32VF103 User Manual

323

15.3.5.

TIMERx registers(x=5,6)

TIMER5 base address: 0x40001000

TIMER6 base address: 0x40001400

Control register 0 (TIMERx_CTL0)

Address offset: 0x00

Reset value: 0x0000

This register can be accessed by half-word (16-bit) or word (32-bit)

Reserved

ARSE

Reserved

SPM

UPS

UPDIS

CEN

Bits

Fields

Descriptions

15:8

Reserved

Must be kept at reset value

ARSE

Auto-reload shadow enable

0: The shadow register for TIMERx_CAR register is disabled

1: The shadow register for TIMERx_CAR register is enabled

6:4

Reserved

Must be kept at reset value

SPM

Single pulse mode.

0: Single pulse mode disable. Counter continues after update event.

1: Single pulse mode enable. The CEN is cleared by hardware and the counter

stops at next update event.

UPS

Update source

This bit is used to select the update event sources by software.

0: When enabled, any of the following events generate an update interrupt or DMA

request:

The UPG bit is set

The counter generates an overflow or underflow event

The slave mode controller generates an update event.

1: When enabled, only counter overflow/underflow generates an update interrupt or

DMA request.

UPDIS

Update disable.

This bit is used to enable or disable the update event generation.

0: update event enable. The update event is generate and the buffered registers are

loaded with their preloaded values when one of the following events occurs:

The UPG bit is set

The counter generates an overflow or underflow event

Summary of Contents for GD32VF103

























































































































































































































































































































































































































































































































































Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands

GigaDevice Semiconductor GD32VF103, User Manual

Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands