GigaDevice Semiconductor GD32VF103 User Manual Download Page 498

Page: 498 / 536

GD32VF103 User Manual

498

IE
P

]

r/rw

IE
P

SAR

]

r/rw

Bits

Fields

Descriptions

31:16

IEPTXFD[15:0]

IN endpoint Tx FIFO depth

In terms of 32-bit words.

≤

HPTXFD

≤

1024

15:0

IEPTXRSAR[15:0]

IN endpoint FIFO Tx RAM start address

The start address for IN endpoint transmit FIFOx is in term of 32-bit words.

21.7.2.

Host control and status registers

Host control register (USBFS_HCTL)

Address offset: 0x0400

Reset value: 0x0000 0000

This register configures the core after power on in host mode. Do not modify it after host

initialization.

This register has to be accessed by word (32-bit)

Rese

rve
d

Rese

rve
d

CLK

]

Summary of Contents for GD32VF103

























































































































































































































































































































































































































































































































































Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands

GigaDevice Semiconductor GD32VF103, User Manual

Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands