GigaDevice Semiconductor GD32VF103 User Manual Download Page 324

Page: 324 / 536

GD32VF103 User Manual

324

The slave mode controller generates an update event.

1: update event disable. The buffered registers keep their value, while the counter

and the prescaler are reinitialized if the UG bit is set or if the slave mode controller

generates a hardware reset event.

CEN

Counter enable

0: Counter disable

1: Counter enable

The CEN bit must be set by software when timer works in external clock, pause

mode and encoder mode. While in event mode, the hardware can set the CEN bit

automatically.

Control register 1 (TIMERx_CTL1)

Address offset: 0x04

Reset value: 0x0000

This register can be accessed by half-word (16-bit) or word (32-bit)

Reserved

MMC[2:0]

Reserved

Bits

Fields

Descriptions

15:7

Reserved

Must be kept at reset value

6:4

MMC[2:0]

Master mode control

These bits control the selection of TRGO signal, which is sent in master mode to

slave timers for synchronization function.

000: Reset. When the UPG bit in the TIMERx_SWEVG register is set or a reset is

generated by the slave mode controller, a TRGO pulse occurs. And in the latter

case, the signal on TRGO is delayed compared to the actual reset.

001: Enable. This mode is useful to start several timers at the same time or to control

a window in which a slave timer is enabled. In this mode the master mode controller

selects the counter enable signal TIMERx_EN as TRGO. The counter enable signal

is set when CEN control bit is set or the trigger input in pause mode is high. There

is a delay between the trigger input in pause mode and the TRGO output, except if

the master-slave mode is selected.

010: Update. In this mode the master mode controller selects the update event as

TRGO.

3:0

Reserved

Must be kept at reset value.

Interrupt enable register (TIMERx_DMAINTEN)

Address offset: 0x0C

Summary of Contents for GD32VF103

























































































































































































































































































































































































































































































































































Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands

GigaDevice Semiconductor GD32VF103, User Manual

Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands