GigaDevice Semiconductor GD32VF103 User Manual Download Page 271

Page: 271 / 536

GD32VF103 User Manual

271

CH2NEN

Channel 2 complementary output enable

Refer to CH0NEN description

CH2P

Channel 2 capture/compare function polarity

Refer to CH0P description

CH2EN

Channel 2 capture/compare function enable

Refer to CH0EN description

CH1NP

Channel 1 complementary output polarity

Refer to CH0NP description

CH1NEN

Channel 1 complementary output enable

Refer to CH0NEN description

CH1P

Channel 1 capture/compare function polarity

Refer to CH0P description

CH1EN

Channel 1 capture/compare function enable

Refer to CH0EN description

CH0NP

Channel 0 complementary output polarity

When channel 0 is configured in output mode, this bit specifies the complementary

output signal polarity.

0: Channel 0 active high

1: Channel 0 active low

This bit cannot be modified when PROT [1:0] bit-filed in TIMERx_CCHP register is

11 or 10 and CH0MS [1:0] bit-filed in TIMERx_CHCTL0 register is 00.

CH0NEN

Channel 0 complementary output enable

When channel 0 is configured in output mode, setting this bit enables the

complementary output in channel0.

0: Channel 0 complementary output disabled

1: Channel 0 complementary output enabled

CH0P

Channel 0 capture/compare function polarity

When channel 0 is configured in output mode, this bit specifies the output signal

polarity.

0: Channel 0 active high

1: Channel 0 active low

When channel 0 is configured in input mode, this bit specifies the CI0 signal polarity.

0: CI0 is non-inverted. Input capture is done on a rising edge of CI0. When used as

extern trigger, CI0 is non-inverted.

1: CI0 is inverted. Input capture is done on a falling edge of CI0. When used as

extern trigger, CI0 is inverted.

This bit cannot be modified when PROT [1:0] bit-filed in TIMERx_CCHP register is

11 or 10.

CH0EN

Channel 0 capture/compare function enable

Summary of Contents for GD32VF103

























































































































































































































































































































































































































































































































































Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands

GigaDevice Semiconductor GD32VF103, User Manual

Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands