manualshive.com logo in svg

GigaDevice Semiconductor GD32VF103, User Manual

The GigaDevice Semiconductor GD32VF103 offers a powerful user manual, essential for seamless operation and troubleshooting. Easily access and download the manual for free from our website, ensuring efficient utilization of this remarkable product. Unlock the full potential of the GD32VF103 with our comprehensive and user-friendly manual.

Share
Download
background image

                                                                                                         

GD32VF103 User Manual

 

350 

 

This bit field cannot be written when the USART is enabled (UEN=1). 

This bit is reserved for UART3/4. 

9 

CPH 

CK phase 

This bit specifies the phase of the CK pin in synchronous mode. 

0: The capture edge of the LSB bit is the first edge of CK pin 

1: The capture edge of the LSB bit is the second edge of CK pin 

This bit field cannot be written when the USART is enabled (UEN=1). 

This bit is reserved for UART3/4. 

8 

CLEN 

CK length 

This bit specifies the length of the CK signal in synchronous mode. 

0: There are 7 CK pulses for an 8 bit frame and 8 CK pulses for a 9 bit frame 

1: There are 8 CK pulses for an 8 bit frame and 9 CK pulses for a 9 bit frame 

This bit field cannot be written when the USART is enabled (UEN=1). 

This bit is reserved for UART3/4. 

7 

Reserved 

Must be kept the reset value 

6 

LBDIE 

LIN break detected interrupt enable 

If this bit is set, an interrupt occurs when the LBDF bit in USART_STAT is set. 

0: LIN break detected interrupt is disabled 

1: LIN break detected interrupt is enabled 

5 

LBLEN 

LIN break frame length 

This bit specifies the length of a LIN break frame. 

0: 10 bits 

1: 11 bits 

This bit field cannot be written when the USART is enabled (UEN=1). 

4 

Reserved 

Must be kept the reset value 

3:0 

ADDR[3:0] 

Address of the USART 

If  it  is configured  toIn  wake  up  by  address  matching  (WM=1),  the  USART  enters 

mute mode when the LSB 4 bits of a received frame do not equal the ADDR[3:0] 

bits, and wakes up when the LSB 4 bits of a received frame equal the ADDR[3:0] 

bits.   

16.4.6. 

Control register 2 (USART_CTL2) 

Address offset: 0x14 

Reset value: 0x0000 0000 

This register has to be accessed by word (32-bit) 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

Reserved 

 

Summary of Contents for GD32VF103

























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32VF103

Lauterbach C2000 Manual preview
C2000
Brand: Lauterbach Pages: 61
Lantronix Device Server UDS 10 Hardware Manual preview
Device Server UDS 10
Brand: Lantronix Pages: 8
National Instruments NI 5922 Calibration Procedure preview
NI 5922
Brand: National Instruments Pages: 28
National Instruments NI 9219 Getting Started preview
NI 9219
Brand: National Instruments Pages: 19
National Instruments NI 6711 User Manual preview
NI 6711
Brand: National Instruments Pages: 103
National Instruments NI PXI-1042 Series Installation Manual preview
NI PXI-1042 Series
Brand: National Instruments Pages: 12
National Instruments PCI-1407 Setup And Operation preview
PCI-1407
Brand: National Instruments Pages: 4
AMD SB710 User Manual preview
SB710
Brand: AMD Pages: 20
Idis DR-8432 Installation Manual preview
DR-8432
Brand: Idis Pages: 31
Automationdirect.com CLICK PLUS C2-02CPU Quick Start Manual preview
CLICK PLUS C2-02CPU
Brand: Automationdirect.com Pages: 10
WHOOP WHT-25LT Quick Start Manual preview
WHT-25LT
Brand: WHOOP Pages: 26
Taiwan Commate Computer Inc. S630MA Quick Installation preview
S630MA
Brand: Taiwan Commate Computer Inc. Pages: 29
ZALMAN CNPS12X User Manual preview
CNPS12X
Brand: ZALMAN Pages: 11
FDI ELI70-CR Quick Start Manual preview
ELI70-CR
Brand: FDI Pages: 2
Kaya Instruments KY-FGK Reference Manual preview
KY-FGK
Brand: Kaya Instruments Pages: 48
ZyXEL Communications ZyAIR B-100 Quick Installation Manual preview
ZyAIR B-100
Brand: ZyXEL Communications Pages: 23
IEI Technology WAFER-EHL Series User Manual preview
WAFER-EHL Series
Brand: IEI Technology Pages: 142
RadioSPECTRAL ICOM IC-7300 Installation Manual preview
ICOM IC-7300
Brand: RadioSPECTRAL Pages: 2

Brands by name

Popular brands

Load more brands