GigaDevice Semiconductor GD32VF103 User Manual Download Page 170

Page: 170 / 536

GD32VF103 User Manual

170

after 14 ADC clock cycles, after the second 14 ADC clock cycles the ADC1 runs again.

Continuous mode can

’

t be used in this mode, because it continuously converts the regular

channel. The behavior of follow-up slow mode shows in the

Figure 11-17. Follow-up slow

mode on 1 channel

After an EOC interrupt is generated by ADC0 (if enabled through the EOCIE bit), we can use

a 32-bit DMA, which transfers to SRAM the ADC_RDATA 32-bit register containing the ADC1

converted data in the upper half-word and the ADC0 converted data in the lower half-word.

Note:

1. The maximum sampling time allowed is <14 ADCCLK cycles to avoid the overlap between

ADC0 and ADC1 sampling phases in the event that they convert the same channel.

2. For both the fast and follow-up slow mode, we must ensure that no external trigger for

inserted channel occurs.

Figure 11-17. Follow-up slow mode on 1 channel

CH1

ADC0

ADC1

Regular

trigger

Sample

Convert

EOC(ADC0 )

EOC(ADC1)

CH1

14 ADCCLK

cycles

14 ADCCLK

cycles

11.6.5.

Trigger rotation mode

This mode can be running on the inserted channel group. The source of external trigger

comes from the inserted channel MUX of ADC0 (selected by the ETSIC[2:0] bits in the

ADC_CTL1 register).

When the first trigger occurs, all the inserted channels of ADC0 are converted. When the

second trigger occurs, all the inserted channels of ADC1 are converted. The behavior of

trigger rotation mode shows in the

Figure 11-18. Trigger rotation: inserted channel group

If the EOIC interrupt of ADC0 and ADC1 are enabled, when all the channels of ADC0 or ADC1

have been converted, the corresponded interrupt occurred.

If another external trigger occurs after all inserted group channels have been converted, the

trigger rotation process restarts by converting ADC0 inserted group channels.

Summary of Contents for GD32VF103

























































































































































































































































































































































































































































































































































Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands

GigaDevice Semiconductor GD32VF103, User Manual

Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands