manualshive.com logo in svg

GigaDevice Semiconductor GD32VF103, User Manual

The GigaDevice Semiconductor GD32VF103 offers a powerful user manual, essential for seamless operation and troubleshooting. Easily access and download the manual for free from our website, ensuring efficient utilization of this remarkable product. Unlock the full potential of the GD32VF103 with our comprehensive and user-friendly manual.

Share
Download
background image

                                                                                                         

GD32VF103 User Manual

 

328 

 

16. 

Universal 

synchronous/asynchronous 

receiver 

/transmitter (USART) 

16.1. 

Overview

 

The Universal Synchronous/Asynchronous Receiver/Transmitter (USART) provides a flexible 

serial data exchange interface. Data frames can be transferred in full duplex or half duplex 

mode,  synchronously  or  asynchronously  through  this  interface. A  programmable  baud  rate 

generator divides the peripheral clock (PCLK1 or PCLK2) to produce a dedicated baud rate 

lock for the USART transmitter and receiver. 

Besides the standard asynchronous receiver and transmitter mode, the USART implements 

several other types of serial data exchange modes, such as IrDA (infrared data association) 

SIR mode, smartcard mode, LIN (local interconnection network) mode, half-duplex mode and 

synchronous mode. It also supports multiprocessor communication mode, and hardware flow 

control protocol (CTS/RTS). The data frame can be transferred from LSB or MSB bit.   

The USART supports DMA function for high-speed data communication, except UART4. 

16.2. 

Characteristics

 

 

NRZ standard format 

 

Asynchronous, full duplex communication 

 

Half duplex single wire communication 

 

Programmable baud-rate generator 

– 

Divided from the peripheral clocks, PCLK2 for USART0, PCLK1 for USART1/2 and 

UART3/4. 

– 

Oversampling by 16 

– 

Maximum speed up to 6.75 MBits/s (PCLK2 108M and oversampling by 16) 

 

Fully programmable serial interface characteristics:   

– 

Even, odd or no-parity bit generation/detection 

– 

A data word length can be 8 or 9 bits 

– 

0.5, 1, 1.5 or 2 stop bit generation 

 

Transmitter and Receiver can be enabled separately 

 

Hardware flow control protocol (CTS/RTS) 

 

DMA request for data buffer access 

 

LIN Break generation and detection 

 

IrDA Support 

 

Synchronous mode and transmitter clock output for synchronous transmission 

 

ISO 7816-3 compliant smartcard interface 

– 

Character mode (T=0) 

Summary of Contents for GD32VF103

























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32VF103

Ubiquiti NanoBeam M5 Setup preview
NanoBeam M5
Brand: Ubiquiti Pages: 3
Commell LS-570 User Manual preview
LS-570
Brand: Commell Pages: 58
Edge-Core SDW100 Quick Start Manual preview
SDW100
Brand: Edge-Core Pages: 7
AXIOMTEK tBOX330-870-FL Series Quick Installation Manual preview
tBOX330-870-FL Series
Brand: AXIOMTEK Pages: 2
Funkwerk TR 200 aw/ bw Operating Instructions preview
TR 200 aw/ bw
Brand: Funkwerk Pages: 2
Tektronix CTS 850 User Manual preview
CTS 850
Brand: Tektronix Pages: 178
ZyXEL Communications ZyXEL ZyAIR B-120 Quick Installation Manual preview
ZyXEL ZyAIR B-120
Brand: ZyXEL Communications Pages: 20
AXAGO PCEU-43R Quick Installation Manual preview
PCEU-43R
Brand: AXAGO Pages: 2
TDK HHM Series HHM2409 Specifications preview
HHM Series HHM2409
Brand: TDK Pages: 2
Intel 640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU User Manual preview
640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU
Brand: Intel Pages: 105
Dahua NVR41-4KS2 Series User Manual preview
NVR41-4KS2 Series
Brand: Dahua Pages: 452
Corsair ELITE LCD UPGRADE KIT Manual preview
ELITE LCD UPGRADE KIT
Brand: Corsair Pages: 11
DayTronic PC-HSICA Instruction Manual preview
PC-HSICA
Brand: DayTronic Pages: 13
IBM Nways 2216 Service And Maintenance Manual preview
Nways 2216
Brand: IBM Pages: 168
SilverStone argon series User Manual preview
argon series
Brand: SilverStone Pages: 16
ZALMAN CNPS9500 AT User Manual preview
CNPS9500 AT
Brand: ZALMAN Pages: 9
A4Tech G6 Saver User Manual preview
G6 Saver
Brand: A4Tech Pages: 8
Rohm BD7682FJ-EVK-301 Quick Start Manual preview
BD7682FJ-EVK-301
Brand: Rohm Pages: 6

Brands by name

Popular brands

Load more brands