GigaDevice Semiconductor GD32VF103 User Manual Download Page 156

Page: 156 / 536

GD32VF103 User Manual

156

11.4.2.

ADC clock

The ADCCLK clock provided by the clock controller is synchronous APB2 clock. The RCU

controller has a dedicated programmable prescaler for the ADC clock.

11.4.3.

ADCON switch

The ADCON bit on the ADC_CTL1 register is the enable switch of the ADC module. The ADC

module will keep in reset state if this bit is 0. For power saving, when this bit is reset, the

analog sub-module will be put into power-down mode.

11.4.4.

Regular and inserted channel groups

The ADC supports 18 multiplexed channels and organizes the conversion results into two

groups: a regular channel group and an inserted channel group.

In the regular group, a sequence of up to 16 conversions can be organized in a specific

sequence. The ADC_RSQ0~ADC_RSQ2 registers specify the selected channels of the

regular group. The RL[3:0] bits in the ADC_RSQ0 register specify the total conversion

sequence length.

In the inserted group, a sequence of up to 4 conversions can be organized in a specific

sequence. The ADC_ISQ register specify the selected channels of the inserted group. The

IL[1:0] bits in the ADC_ISQ register specify the total conversion sequence length.

11.4.5.

Conversion modes

Single conversion mode

This mode can be running on both regular and inserted channel group. In the single

conversion mode, the ADC performs conversion on the channel specified in the RSQ0[4:0]

bits of ADC_RSQ2 at a regular trigger or the channel specified in the ISQ3[4:0] bits of

ADC_ISQ. When the ADCON has been set high, the ADC samples and converts a single

channel, once the corresponding software trigger or external trigger is active.

Figure 11-2. Single conversion mode

CH2

EOC

Regular

trigger

Sample

Convert

After conversion of a single regular channel, the conversion data will be stored in the

ADC_RDATA register, the EOC will be set. An interrupt will be generated if the EOCIE bit is

set.

Summary of Contents for GD32VF103

























































































































































































































































































































































































































































































































































Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands

GigaDevice Semiconductor GD32VF103, User Manual

Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands