GigaDevice Semiconductor GD32VF103 User Manual Download Page 160

Page: 160 / 536

GD32VF103 User Manual

160

Figure 11-6. Discontinuous conversion mode

CH2

CH1

CH5

CH7

CH11

CH16

CH2

CH1

· · ·

Inserted

trigger

EOC

One circle of regular group, RL=7, DISNUM=2

CH9

CH10

CH8

CH9

CH10

· · ·

EOIC

One circle of inserted group, IL=2

Regular

trigger

Sample

Convert

CH12

CH17

CH5

Software procedure for discontinuous conversion on a regular channel group:

Set the DISRC bit in the ADC_CTL0 register and the DMA bit in the ADC_CTL1 register

Configure DISNUM[2:0] bits in the ADC_CTL0 register

Configure ADC_RSQx and ADC_SAMPTx registers

Configure ETERC and ETSRC bits in the ADC_CTL1 register if in need

Prepare the DMA module to transfer data from the ADC_RDATA (refer to the spec of the

DMA

module).

Set the SWRCST bit, or generate an external trigger for the regular group

Repeat step6 if in need.

Wait the EOC flag to be set

Clear the EOC flag by writing 0 to it

Software procedure for discontinuous conversion on an inserted channel group:

Set the DISIC bit in the ADC_CTL0 register

Configure ADC_ISQ and ADC_SAMPTx registers

Configure ETEIC and ETSIC bits in the ADC_CTL1 register if in need

Set the SWICST bit, or generate an external trigger for the inserted group

Repeat step4 if in need

Wait the EOC/EOIC flags to be set

Read the converted in the ADC_IDATAx register

Clear the EOC/EOIC flag by writing 0 to them

11.4.6.

Inserted channel management

Auto-insertion

The inserted group channels are automatically converted after the regular group channels

when the ICA bit in ADC_CTL0 register is set. In this mode, external trigger on inserted

channels cannot be enabled. A sequence of up to 20 conversions programmed in the

ADC_RSQ0~ADC_RSQ2 and ADC_ISQ registers can be used to convert in this mode. In

addition to the ICA bit, if the CTN bit is also set, regular channels followed by inserted

channels are continuously converted.

Summary of Contents for GD32VF103

























































































































































































































































































































































































































































































































































Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands

GigaDevice Semiconductor GD32VF103, User Manual

Search results

Summary of Contents for GD32VF103

Reviews:

Related manuals for GD32VF103

Brands by name

Popular brands