gefran TPD32-EV-...-2B, Instructions Manual

Page: 66 / 504

—————— TPD32-EV ——————
66
Table 4.3.4: Wire adapter Kit and lugs suggested for UL approval
The following sizes are not provided with pressure connectors. Recommended compression lugs are in the fol -
lowing table. For sizes up to 56A any UL listed lug, sized for the indicated bolt and AWG or MCM cable, is
suitable for this use, otherwise a compression lug type from ILSCO or BURNDY (YA...) or Grainger (3L...)
manufacturer is specified.
Device type Terminals AWG o MCM Lug type Bolt diameter [mm]
Tightening torque
[Nm]
TPD32-EV-.../...-17-....-A-NA U-V-W-C-D-PE 12 any 5 2-3
TPD32-EV-.../...-35-....-A-NA U-V-W-C-D-PE 8 any 5 2,5-3
TPD32-EV-.../...-56-....-A-NA U-V-W-C-D-PE 4 any 5 2,5-3
TPD32-EV-.../...-88-....-A-NA U-V-W-C-D-PE
See table below TPD32-EV-.../...-112-....-A-NA U-V-W-C-D-PE
TPD32-EV-.../...-148-....-A-NA U-V-W-C-D-PE
TPD32-EV-.../...-224-..-B-NA
U-V-W 2 x 1 YA1CL6-BOX M10 25
C-D 2 x 2/0 YA26L6-BOX M10 25
PE M8 15
TPD32-EV-.../...-280-..-B-NA
U-V-W 2 x 2/0 YA26L6-BOX M10 25
C-D 2 x 3/0 YA27L-BOX M10 25
PE M8 15
TPD32-EV-.../...-336-..-B-NA
U-V-W 2 x 250 YA27L-BOX M10 25
C-D 2 x 3/0 YA29L-BOX M10 25
PE M8 15
TPD32-EV-.../...-400-..-B-NA
U-V-W 2 x 250 YA29L-BOX, M10 25
C-D 2 x 300; serve kit YA30L M10 25
PE M8 15
TPD32-EV-.../...-450-..-B-NA
U-V-W 2 x 300; serve kit YA30L7 M10 25
C-D 2 x 400; serve kit YA32L M10 25
PE M8 15
TPD32-EV-.../...-490-..-C-NA
U-V-W 3 x 3/0 YA27L-BOX M10 25
C-D 4 x 2/0 YA26L6-BOX M10 25
PE 1/0 YA25L6-BOX M8 15
TPD32-EV-.../...-560-..-C-NA
U-V-W 3 x 3/0 YA27L-BOX M10 25
C-D 4 x 2/0 YA26L6-BOX M10 25
PE M8 15
TPD32-EV-.../...-750-..-C-NA
U-V-W 4 x 4/0 YA28L-BOX 2 x M10 25
C-D 4 x 300, serve kit YA30L 2 x M10 25
PE 2/0 YA26L6-BOX M8 15
TPD32-EV-.../...-800-..-C-NA
U-V-W-C-D 4 x 250 CRA-250 o CRA-250L M10 25
PE M8 15
TPD32-EV-.../...-850-..-C-NA
U-V-W-C-D 4 x 300, serve kit CRA-300 o CRA-300L M10 25
PE M8 15
TPD32-EV-.../...-980-..-D-NA
U-V-W 4 x 300 3LM58 4 x M12 45
C-D 4 x 500 3LM61 4 x M12 45
PE 2 x 300 3LM58 4 x M12 45
TPD32-EV-.../...-1000-..-D-NA
U-V-W 4 x 350 3LM59 4 x M12 45
C-D 4 x 500 3LM61 4 x M12 45
PE 4 x 350 3LM59 4 x M12 45
TPD32-EV-.../...-1200-..-D-NA
U-V-W
4 x 500
with EAM 2617_1 adapter
3LM61 4 x M12 45
C-D
5 x 500
with EAM 2617_3 adapter
3LM61 4 x M12 45
PE 2 x 500 3LM61 4 x M12 45
TPD32-EV-.../...-1500-..-D-NA
U-V-W
5 x 500
with EAM 2617_1 adapter
3LM61 4 x M12 45
C-D
6 x 500
with EAM 2617_3 adapter
3LM61 4 x M12 45
PE 3 x 350 3LM59 4 x M12 45
TPD32-EV-.../...-1800-..-D-NA
U-V-W
6 x 500
with EAM 2617_1 adapter
3LM61 4 x M12 45
C-D Use Cu-bar or Eriflex "Flexibar" - 4 x M12 45
PE 3 x 500 3LM61 4 x M12 45
TPD32-EV-.../...-1850-..-D-NA
U-V-W
6 x 500
with EAM 2617_1 adapter
3LM61 4 x M12 45
C-D Use Cu-bar or Eriflex "Flexibar" - 4 x M12 45
PE 3 x 500 3LM61 4 x M12 45
2x means that two compression lugs of the specified type have to be used on the opposite side of the busbar.
4x means that four compression lugs of the specified type have to be used on the same busbar, two for each side and one for each bolt hole.
Bolt, nuts and washers are factory mounted on output busbars. The required ILSCO compression tool is marked on each terminal plug.