gefran TPD32-EV-...-2B, Instructions Manual

Page: 220 / 504

—————— TPD32-EV ——————
220
Parameter N.
Value
Standard
configuration
min max
factory
America
factory
Standard
Inversion in 3
Enabled (1) / Disabled (0)
1269 0 1 Disabled (0) Disabled (0)
Inversion in 4
Enabled (1) / Disabled (0)
1270 0 1 Disabled (0) Disabled (0)
Digital in 5
149 0 87 OFF (0) OFF (0)
Inversion in 5
Enabled (1) / Disabled (0)
1271 0 1 Disabled (0) Disabled (0)
Digital in 6
150 0 87 OFF (0) OFF (0)
Inversion in 6
Enabled (1) / Disabled (0)
1272 0 1 Disabled (0) Disabled (0)
Digital in 7
151 0 87 OFF (0) OFF (0)
Inversion in 7
Enabled (1) / Disabled (0)
1273 0 1 Disabled (0) Disabled (0)
Digital in 8
152 0 87 OFF (0) OFF (0)
Inversion in 8
Enabled (1) / Disabled (0)
1274 0 1 Disabled (0) Disabled (0)
Digital input XX Selection of the parameter that is addressed by the digital input concerned. The follow -
ing assignments are possible:
OFF
Motor pot reset
Motor pot up
Motor pot down
Motor pot sign +
Motor pot sign -
Jog +
Jog -
Failure reset
Torque reduct
Ramp out = 0
Ramp in = 0
Freeze ramp
Lock speed reg
Lock speed I
Auto capture
Input 1 sign +
1)
Input 1 sign -
1)
Input 2 sign +
1)
Input 2 sign -
1)
Input 3 sign +
1)
Input 3 sign -
1)
Zero torque
Speed sel 0
2)
Speed sel 1
2)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Speed sel 2
2)
Ramp sel 0
3)
Ramp sel 1
3)
Field loss
Enable flux reg
Enable flux weak
Pad A bit 0
Pad A bit 1
Pad A bit 2
Pad A bit 3
Pad A bit 4
Pad A bit 5
Pad A bit 6
Pad A bit 7
Forward sign
Reverse sign
An in 1 target
An in 2 target
An in 3 target
Enable droop
Enable PI PID
4)
Enable PD PID
4)
PI integral freeze
4)
PID offs. Sel
4)
PI central vs0
4)
25
26
27
29
30
31
32
33
34
35
36
37
38
39
44
45
46
47
48
49
52
53
54
55
56
PI central vs1
4)
Diameter calc
4)
Diam reset
Diam calc Dis
Torque winder EN
Line acc status
Line dec status
Line fstp status
Speed match
Diam inc/dec En
Wind/unwind
Diam preset SEL0
Diam preset SEL1
Taper enable
Speed demand En
Winder side
Enable PI-PD PID
Jog TW enable
Brake fbk
5)
Adapt Sel 1
6)
Adapt Sel 2
7)
Wired FC EN
(8)
Wired FC Inv Seq
(9)
Wired FC Act Brg
(10)
57
58
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
86
87
88
89
90
1)
The Input xx sign + and Input XX sign - parameters can only be used in conjunction
with the other parameter.
2)
The Speed sel 0 , Speed sel 1 and Speed sel 2 parameters can only be used together.
3)
The Ramp sel 0 and Ramp sel 1 parameters can only be used together.
4)
Refer to paragraph 6.16.3 PID function
5)
External mechanical brake relay feedback; if set to digital input (selection: Brake
fbk), this command is necessary in order for the brake to be released or closed
without triggering the alarm. If not set to digital input, it is not considered in the
brake control sequence.
6)
Gains value selection with the significance 2
1
7)
Gains value selection with the significance 2
2
8)
Enables field control by TPD32-EV-FC via standard I/O.
9)
Indication if field control is during inversion sequence
10)
Indication of the actual active bridge (positive or negative) of the FC unit