Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 299 | Manualshive

Page: 299 / 320

background image

7.4 Disk Drive Removal Procedure

7.4 Disk Drive Removal Procedure

The method and procedures to demount the disk drive to check the jumper
terminal, change the jumper position, or replace the device differ depend on the
system cabinet structure. Therefore, for actual working procedures, the specific
conditions necessary for each system must be determined. The general removal
procedures, with notes, are as follows.

a) Disconnect the power-interface cable.

b) Remove the screws that attach the drive and remove the drive from the system

cabinet.

c) When storing or transporting the drive, pack it an antistatic bag in compliance

with section 7.1.2 (5) d. and (5) e..

To protect the device from damage and prevent the worker getting hurt, observe
the following cautions and precautions in Subsection 7.1.1.

Damage or Device damage

1.

Perform any removal after the system power is completely
disconnected. The cable must not be disconnected and the
screws that attach the drive must not be removed with the
power ON.

2.

Do not move the drive and attach or detach the connector until
it comes to a complete stop (about 30 s after the power is
turned OFF).

3.

Perform the human body grounding to discharge any static
electricity from your body. (Be sure to wear a wrist strap)

7.5 Spare Disk Drive

See Subsection 1.2.2, "Model and product number," to order a disk drive for
replacement or as a spare.

C141-E280

7-15

«
...
297
298
299
300
301
...
»

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments

Related manuals for MHZ2080BJ

XCubeSAN XS5224D

Brand: Qsan Technology Pages: 143

4big Spare Drive

Brand: LaCie Pages: 24

Taylor-Wharton XL-65

Brand: Harsco Pages: 26

Brand: morse Pages: 6

Brand: OCZ Pages: 3

Beside Storage Pantry

Brand: Haworth Pages: 6

DataPort 25 Enhanced Carrier

Brand: CRU Dataport Pages: 2

Brand: U-Line Pages: 3

Brand: Panasonic Pages: 33

Brand: Panasonic Pages: 48

Brand: Salsbury Industries Pages: 5

SO READY Secure

Brand: DANE-ELEC Pages: 2

Brand: ABSCO SHEDS Pages: 20

Brand: ABSCO SHEDS Pages: 24

Brand: Certa Pages: 8

Brand: Promise Technology Pages: 170

Brand: LapSafe Pages: 7

Brand: EverFocus Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands