manualshive.com logo in svg

Fujitsu MHZ2080BJ, Product/Maintenance Manual, Page: 120 / 320

Share
Download
Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 120

Interface 

 

(10)  STANDBY IMMEDIATE (X '94' or X 'E0')  

Upon receipt of this command, the device enters the standby mode.  The device 
then reports the status to the host system.  This command does not support the 
APS timer function. 

• 

Error reporting conditions 

(1)  A SATA communication error occurred (ST = 51h, ER = 14h). 

 

At command issuance (Shadow Block Registers setting contents) 

CM 

X '94' or X 'E0' 

DH 

x x x x 

xx 

CH 

CL 

SN 

SC 

FR 

xx 

xx 

xx 

xx 

Xx 

 
 

At command completion (Shadow Block Registers contents to be read) 

ST Status 

information 

DH 

x x x x 

xx 

CH 

CL 

SN 

SC 

ER 

xx 

xx 

xx 

xx 

Error information 

 

5-46 

C141-E280 

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments