Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 250

Page: 250 / 320

Interface

5.4.1 Non-data command protocol

Execution of the following commands does not involve data transfer between the
host and the device.

•

RECALIBRATE

•

SMART ENABLE/DISABLE AUTOSAVE

•

SMART RETURN STATUS

•

FLUSH CACHE (EXT)

•

SEEK

•

READ VERIFY SECTOR(S) (EXT)

•

WRITE UNCORRECTABLE EXT

•

EXECUTE DEVICE DIAGNOSTIC

•

INITIALIZE DEVICE PARAMETERS

•

SET FEATURES

•

SET MULTIPLE MODE

•

READ NATIVE MAX ADDRESS (EXT)

•

SET MAX ADDRESS (EXT)

•

SET MAX LOCK

•

SET MAX FREEZE LOCK

•

IDLE

•

IDLE (UNLOAD) IMMEDIATE

•

STANDBY

•

STANDBY IMMEDIATE

•

CHECK POWER MODE

•

SMART DISABLE OPERATION

•

SMART ENABLE OPERATION

•

SMART EXECUTE OFFLINE IMMEDIATE

•

SECURITY ERASE PREPARE

•

SECURITY FREEZE LOCK

5-176

C141-E280

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Search results

Summary of Contents for MHZ2080BJ

Reviews:

Fujitsu MHZ2080BJ, Product/Maintenance Manual, Page: 250 / 320

Search results

Summary of Contents for MHZ2080BJ

Reviews: