manualshive.com logo in svg

Fujitsu MHZ2080BJ, Product/Maintenance Manual, Page: 158 / 320

Share
Download
Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 158

Interface 

 

(17)  DEVICE CONFIGURATION (X 'B1')  

Individual Device Configuration Overlay feature sub commands are identified by 
the value placed in the Features field.  The following table shows these Features 
field values.  If this command sets with the reserved value of Features field, an 
aborted command error is posted. 

 

FR field 

Command 

C0h 

DEVICE CONFIGURATION RESTORE 

C1h 

DEVICE CONFIGURATION FREEZE 

C2h 

DEVICE CONFIGURATION IDENTIFY 

C3h 

DEVICE CONFIGURATION SET 

00h to BFh, 

C4h to FFh 

Reserved 

 
 

At command issuance (Shadow Block Registers setting contents) 

CM 

1 0 1 1 0 0 0  1 

DH 

x x x x 

xx 

CH 

CL 

SN 

SC 

xx 

xx 

xx 

xx 

FR C0h/C1h/C2h/C3h 

 
 

At command completion (Shadow Block Registers contents to be read) 

ST Status 

information 

DH 

x x x x 

xx 

CH 

CL 

SN 

SC 

xx 

xx 

xx 

xx 

ER Error 

information 

 

5-84 

C141-E280 

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments