Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 298 | Manualshive

Page: 298 / 320

background image

Maintenance and Diagnosis

7.3.3 Troubleshooting at factory

When the trouble is recovered by replacing the drive at field (Subsection 7.3.2),
troubleshoot the replaced drive to isolate the trouble to the subassembly parts.

To shorten the troubleshooting time and repairing time, gather the data, such as
environmental data and other information, from the user and then return the failed
drive to the factory to repair.

At the factory, user environment is made and a reappearance test is performed. To
reappearance a same trouble at user, the failed drive is connected to the host
system. If no trouble occurs by the normal test, the reappearance test is performed
by adding the voltage/temperature load using a disk drive tester or tools according
to the user environment.

When a trouble reappeared, troubleshoot the cause of failure. Then, replace the
failed unit or parts.

As this level maintenance is made by a factory, this maintenance level is beyond
the scope of this manual.

Device damage

The disk enclosure (DE) must never to be opened in the field.
Opening the disk enclosure may cause irreparable damage.

7-14

C141-E280

«
...
296
297
298
299
300
...
»

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments

Related manuals for MHZ2080BJ

Brand: G-Technology Pages: 32

Brand: G-Technology Pages: 35

Brand: X-METAL Pages: 36

GLADIATOR PLUS 2

Brand: Asgard Pages: 6

Cold Frame Single

Brand: Palram Pages: 11

Brand: Et Pages: 22

Brand: Olixir Pages: 2

Expansion 750GB

Brand: Seagate Pages: 1

IC25N040ATCS04 - Travelstar 40 GB Hard Drive

Brand: IBM Pages: 217

Brand: oldfields Treco Pages: 28

QuantaGrid D51PH-1ULH

Brand: QCT Pages: 167

GEAR 175-9872-4

Brand: Yukon Pages: 7

DataPort 25 Enhanced Carrier

Brand: CRU Dataport Pages: 2

Brand: JVC Pages: 2

TS-401T Turbo Server

Brand: QNAP Pages: 8

Brand: TrueNAS Pages: 12

Store 'n' Go Hi-Speed USB

Brand: Verbatim Pages: 15

Traveling Disk U250

Brand: PQI Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands