Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 128 | Manualshive

Page: 128 / 320

background image

Interface

(16) SMART (X 'B0')

This command predicts the occurrence of device failures depending on the
subcommand specified in the Features field. If the Features field contains values
that are not supported with the command, the Aborted Command error is issued.

Before issuing the command, the host must set the key values in the Cylinder Low
and Cylinder High field (4Fh in the Cylinder Low field and C2h in the Cylinder
High field). If the key values are incorrect, the Aborted Command error is issued.

If the failure prediction function is disabled, the device returns the Aborted
Command error to subcommands other than those of the SMART Enable
Operations (with the Features field set to D8h).

If the failure prediction function is enabled, the device collects and updates data on
specific items. The values of items whose data is collected and updated by the
device in order to predict device failures are hereinafter referred to as attribute
values.

5-54

C141-E280

«
...
126
127
128
129
130
...
»

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments

Related manuals for MHZ2080BJ

Brand: LaCie Pages: 22

Z-DRIVE R2 E88 512GB PCI-EXPRESS X8 SSD

Brand: OCZ Pages: 2

Brand: NEC Pages: 254

G-DRIVE mobile USB

Brand: G-Technology Pages: 32

Brand: LaCie Pages: 22

BARRACUDA ST32000542AS

Brand: Seagate Pages: 2

Brand: Eneo Pages: 12

Brand: CalDigit Pages: 16

actiLib Library 2U

Brand: Actidata Pages: 17

Brand: Broadcom Pages: 24

Brand: Allnet Pages: 148

Brand: WOOD feeling Pages: 27

Brand: Rowlinson Garden Products Pages: 2

Brand: Rowlinson Garden Products Pages: 5

Leopold Bench Kit

Brand: Austin Kontore Pages: 12

Brand: Teac Pages: 2

SuperStorage 6028R-E1CR12H

Brand: Supermicro Pages: 140

Brand: Corvus systems Pages: 291

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands