manualshive.com logo in svg

Fujitsu MHZ2080BJ, Product/Maintenance Manual, Page: 221 / 320

Share
Download
Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 221

 

5.3  Host Commands 

(40)  READ MULTIPLE EXT (X '29') 

• 

Description 

This command is the extended command of the READ MULTIPLE command.  
The LBA specification is increased from 28 bits to 48 bits, and the maximum 
number of sectors that can be transferred by a single command is changed from 
100h to 10000h.  Other command controls are the same as those of the READ 
MULTIPLE command. 

• 

Error reporting conditions 

At command issuance (Shadow Block Registers setting contents) 

(1)  The command was issued in CHS mode (ST = 51h, ER = 04h). 

The other error reporting conditions are the same as those of the READ 
MULTIPLE command. 

 

CM 

0 0 1 0 

1 

1 0 0 

DH 

1 L 1 x 

xx 

CH EXP 

CH 

CL EXP 

CL 

SN EXP 

LBA (39-32) 

Sector count (15-8) 

xx 

SN 

SC EXP 

SC 

FR EXP 

FR 

LBA (47-40) 

LBA (23-16) 

LBA (15-8) 

LBA (31-24) 

LBA (7-0) 

Sector count (7-0) 

xx 

 
 

At command completion (Shadow Block Registers contents to be read) 

ST Status 

information 

DH 

1 

1 L 

x 

xx 

CH EXP 

CH 

CL EXP 

CL 

SN EXP 

SN 

SC EXP 

SC 

ER 

LBA (47-40) 

LBA (23-16) 

LBA (39-32) 

LBA (15-8) 

LBA (31-24) 

LBA (7-0) 

xx 

xx 

Error information 

C141-E280 

5-147 

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments