Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 302 | Manualshive

Page: 302 / 320

background image

Glossary

Master (Device 0)

The master is the first drive that can operate on the AT bus. The master is daisy-
chained with the second drive which can operate in conformity with the ATA
standard.

MTBF

Mean time between failures. The MTBF is calculated by dividing the total
operation time (total power-on time) by the number of failures in the disk drive
during operation.

MTTR

Mean time to repair. The MTTR is the average time required for a service person
to diagnose and repair a faulty drive.

PIO (Programmed input-output)

Mode to transfer data under control of the host CPU

Positioning

Sum of the seek time and mean rotational delay

Power save mode

The power save modes are idle mode, standby mode, and sleep mode.

In idle mode, the drive is neither reading, writing, nor seeking data. In standby
mode, the spindle motor is stopped and circuits other than the interface control
circuit are sleeping. The drive enters sleep mode when the host issues the SLEEP
command.

Reserved

Reserved bits, bytes, and fields are set to zero and unusable because they are
reserved for future standards.

Rotational delay

Time delay due to disk rotation. The mean delay is the time required for half a
disk rotation. The mean delay is the average time required for a head to reach a
sector after the head is positioned on a track.

Seek time

The seek time is the time required for a head to move from the current track to
another track. The seek time does not include the mean rotational delay.

GL-2

C141-E280

«
...
300
301
302
303
304
...
»

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments

Related manuals for MHZ2080BJ

Brand: LaCie Pages: 25

BladeCenter Management Module

Brand: IBM Pages: 82

TrueNAS R Series

Brand: iXsystems Pages: 24

Brand: Transcend Pages: 24

TS-H686-D1602-8G

Brand: QNAP Pages: 12

Brand: z Pages: 45

Brand: LaCie Pages: 22

FlashPen USB 2.0 Piko Business

Brand: Hama Pages: 4

Travelstar 14GS

Brand: IBM Pages: 2

My Passport Essential SE

Brand: Western Digital Pages: 2

Brand: NetApp Pages: 9

Brand: SanDisk Pages: 2

Brand: 8BitMods Pages: 15

Brand: Rocstor Pages: 59

Brand: Sealey Pages: 2

Brand: Sealey Pages: 3

Brand: Sealey Pages: 2

Brand: Sealey Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands