manualshive.com logo in svg

Fujitsu MHZ2080BJ, Product/Maintenance Manual, Page: 145 / 320

Share
Download
Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 145

 

5.3  Host Commands 

Table 5.23  SCT command and the function 

Sector Number 

field 

Features field

Function 

X 'E0' 

X 'D5' 

SCT STATUS REQUEST: 

A device that received this subcommand transfers Status 
information of SCT in 512 bytes to the host. 

*  For information about the format of the SCT Status, see 

Table 5.24. 

X 'E0' 

X 'D6' 

SCT COMMAND SET: 

A device that received this subcommand and the Key Sector 
Format data of 512 bytes is received from the host, and a 
device execute the specific operation for which the action 
code. 

*  For information about the format of the Key Sector 

Format, see Table 5.27 to Table 5.30. 

X 'E1' 

X 'D5' 

SCT READ DATA: 

A device that received this subcommand transfers the data 
table of the number of sectors specified with Sector Count 
field to the host.  It is necessary to issue the SCT 
COMMAND SET immediately before when this command is 
issued. 

X 'E1' 

X 'D6' 

SCT WRITE DATA: 

A device that received this subcommand and the Data Table 
of the number of sectors specified with Sector Count field 
from the host, and a device execute the write operation.  It is 
necessary to issue the SCT COMMAND SET immediately 
before when this command is issued. 

 

C141-E280 

5-71 

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments