manualshive.com logo in svg

Fujitsu MHZ2080BJ, Product/Maintenance Manual, Page: 204 / 320

Share
Download
Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 204

Interface 

 

(31)  SECURITY ERASE PREPARE (X 'F3')  

The SECURITY ERASE UNIT command feature is enabled by issuing the 
SECURITY ERASE PREPARE command and then the SECURITY ERASE 
UNIT command.  The SECURITY ERASE PREPARE command prevents data 
from being erased unnecessarily by the SECURITY ERASE UNIT command. 

• 

Error reporting conditions 

(1)  The device is in Security Frozen mode (ST = 51h, ER = 04h). 

(2)  A SATA communication error occurred (ST = 51h, ER = 14h). 

 

At command issuance (Shadow Block Registers setting contents) 

CM 

1 1 1 1 0 0 1  1 

DH 

x x x x 

xx 

CH 

CL 

SN 

SC 

FR 

xx 

xx 

xx 

xx 

xx 

 
 

At command completion (Shadow Block Registers contents to be read) 

ST Status 

information 

DH 

x x x x 

xx 

CH 

CL 

SN 

SC 

ER 

xx 

xx 

xx 

xx 

Error information 

 

5-130 

C141-E280 

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments