Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 192 | Manualshive

Page: 192 / 320

background image

Interface

*33 WORD 220: Write Read Verify mode (Optional)

Verify mode display when Write Read Verify function is set by SET
FEATURES command.

Bits 15-8: Reserved

Bits 7-0:

Verify mode display Value: 00h-03h

*34 WORD 234: Minimum number of 512Byte units per DOWNLOAD

MICROCODE command mode 3

When the command for which mode 3(FR reg = 03h) is specified with
DOWNLOAD MICROCODE (0x92) is issued, the host is a unit of possible
transfer of the minimum transfer sector.

Value: 0001h

sector

*35 WORD 235: Maximum number of 512Byte units per DOWNLOAD

MICROCODE command mode3

When the command for which mode 3(FR reg = 03h) is specified with
DOWNLOAD

MICROCODE (0x92) is issued, the host is a unit of possible transfer of the
maximum transfer sector.

8MByte Buffer drive Value: 0B00h sector

5-118

C141-E280

«
...
190
191
192
193
194
...
»

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments

Related manuals for MHZ2080BJ

ShareCenter Pro DNS-1200-05

Brand: D-Link Pages: 68

Brand: D-Link Pages: 10

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 8

TotalStorage DS4800

Brand: IBM Pages: 250

TotalStorage DS4800

Brand: IBM Pages: 234

Brand: IBM Pages: 136

System Storage DS5020

Brand: IBM Pages: 31

Netfinity EXP300

Brand: IBM Pages: 93

Brand: IBM Pages: 270

Ultrastar 36LZX

Brand: IBM Pages: 2

DCAS-32160 - Ultrastar 2.1 GB Hard Drive

Brand: IBM Pages: 232

System Storage TS3310

Brand: IBM Pages: 531

Brand: StarTech.com Pages: 8

Brand: LaCie Pages: 2

Brand: Seagate Pages: 44

XCubeNXT XN8012D

Brand: Qsan Technology Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands