Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 264 | Manualshive

Page: 264 / 320

background image

Operations

6.1 Reset and Diagnosis

This section explains the device responses to power-on and an accepted reset.

6.1.1 Response to power-on

Immediately after power is turned on, the host sets 0x7Fh in the Status field of the
Shadow Block and 0xFFh in other fields. After communication with the SATA
interface is established, the host sets 0xFFh in the Status field of the Shadow
Block. The device establishes communication with the SATA interface (PHY
Ready) within 10 ms. The device sends the FIS (STS = 50h) to notify the host that
the device is ready.

Note: Figure 6.1 assumes that power is turned on after the power-off state

continued for more than five seconds.

Figure 6.1 Response to power-on (when the host is powered

on earlier than the device)

6-2

C141-E280

«
...
262
263
264
265
266
...
»

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments

Related manuals for MHZ2080BJ

Brand: Quest Engineering Pages: 540

Brand: U-Line Pages: 3

Brand: U-Line Pages: 6

EliteRAID ER104I+

Brand: Sans Digital Pages: 64

Brand: Zhejiang Longyard Trade Industrial Pages: 18

TOWERRAID TR4M+

Brand: Sans Digital Pages: 1

SiliconEdge Blue Series

Brand: Western Digital Pages: 2

Brand: Eminent Pages: 112

Supporter AM 1200 FH

Brand: Beck Pages: 32

Brand: Archos Pages: 12

Brand: Western Digital Pages: 2

TERASTATION HS-D1.0TGL/R5

Brand: Buffalo Pages: 2

Brand: Seagate Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands