Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 118

Page: 118 / 320

Interface

Table 5.7 Operation of DOWNLOAD MICROCODE

Host Command

Movement of device

Subcommand

code

(FR Field)

Sector Offset

(CH, CL Field)

Sector count

(SN, SC Field)

Data

transfer

Microcode rewriting execution

0000h

Non

Rewriting execution reservation

01h ----

xxxxh

It is.

Rewriting execution reservation

0000h

Non

Rewriting execution reservation

03h xxxxh

xxxxh

It is.

Rewriting execution reservation

0000h Non

Execution.

07h ----

xxxxh

It is.

Execution. *2

Excluding 01h,

03h

and 07h

−

Abort

*1: When FR Field = 03 (Mode3) is specified, Abort is returned as an error when

the specification of doing Sector Offset (CH, CL Field) is the transfer end the
last sector and is not consecutive.

Moreover, Sector Offset (CH, CL Field) is invalid in specification other than
FR Field = 03 (Mode3).

*2: In the following cases, Subcommand code = 07h returns Abort as an error

though becomes Microcode rewriting execution specification.

1) Abnormality of the transmitted Microcode data is detected.

2) The data transfer is not done (The number of transfer: 0).

3) The DOWNLOAD MICROCODE command is not continuously issued when

the transfer has been divided into multiple transfers.

5-44

C141-E280

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Search results

Summary of Contents for MHZ2080BJ

Reviews:

Related manuals for MHZ2080BJ

Brands by name

Popular brands

Fujitsu MHZ2080BJ, Product/Maintenance Manual

Search results

Summary of Contents for MHZ2080BJ

Reviews:

Related manuals for MHZ2080BJ

Brands by name

Popular brands